CLP80-020
Features
Linear bearings are used to achieve a sliding frequency of
10 million times.
10 million times.
The built-in sensor is magnetic, giving it excellent environmental resistance.
![Contact Linear Pulse Coder CLP80-020](../../wp-content/themes/levex/img/products/14/top_01.jpg)
Specification
Model | CLP80-020 | |
---|---|---|
Sensor diameter (mm) | φ8 | |
Measuring range | 20㎜ *Range of movement:24mm | |
Mechanical response | About 16Hz | |
Force Measured | Max. 1.7N (See the graph below, Force Measured – Output Characteristics [when set facing downward]) | |
Linearity | ±1.5%/FS or less | |
Temperature characteristics | 1%/FS or less(0~60℃) | |
Operating temperature range(℃) | -10~70 | |
Lead-out cable | Length (m) | 1.5 |
Outer diameter | Φ2.4 twisted pair shielded cable |
Force Measured – Output Characteristics
![Force Measured - Output Characteristics](../../wp-content/themes/levex/img/en/products/14/img_03.jpg)
Outline drawing
![Outline drawing](../../wp-content/themes/levex/img/en/products/14/img_02.jpg)
CLP35-008
Features
The φ3.5 mm-diameter probe is achieved by building in an ultra-fine sensor.
The built-in sensor is magnetic, giving it excellent environmental resistance.
![Contact Linear Pulse Coder CLP35-008](../../wp-content/themes/levex/img/products/14/top_02.jpg)
Specification
Model | CLP35-008 | |
---|---|---|
Sensor diameter(mm) | φ3.5 | |
Measuring range | 8㎜ *Range of movement:10mm | |
Mechanical response | 約10Hz | |
Force Measured | Max.0.6N (See the graph below, Force Measured – Output Characteristics [when set facing downward]) | |
Linearity | ±2%/FS or less | |
Temperature characteristics | ±1.5%/FS or less | |
Operating temperature range(℃) | -10~70 | |
Lead-out cable | Length(m) | 2 |
Outer diameter | Φ1.3 twisted pair shielded cable |
Force Measured – Output Characteristics
![Force Measured - Output Characteristics](../../wp-content/themes/levex/img/en/products/14/img_06.jpg)
Outline drawing
![Outline drawing](../../wp-content/themes/levex/img/en/products/14/img_05.jpg)
Precautions for Use
– Do not fix with metal fittings or screws except for the sensor fixing part.
– If there is metal surrounding the hatched part, the output voltage may drop.
– If there is metal surrounding the hatched part, the output voltage may drop.
![Precautions for Use](../../wp-content/themes/levex/img/en/products/14/img_07.jpg)
Converter(CV05/CVS5/Mold)
Amplifier
Specification
Model | CV05 | CVS5 CVS5(Resin case type) |
---|---|---|
Power-supply voltage | DC12~24V ±10% | DC9~16V ±10% |
Current consumption | 40mA or less | |
Output voltage | Analog output DC1~5V | |
Resolution | Approx 1/2000 of measuring range | |
Responsiveness | About 4kHz(-3dB) | |
Operating temperature range | -20~80℃ (No condensation) | |
Temperature characteristics | 0.025%/FS or less (0 to 60℃ @ center of measurement range) |
Outline drawing
CV05
![CV05](../../wp-content/themes/levex/img/products/05/img_05.jpg)
![CV05](../../wp-content/themes/levex/img/en/products/05/img_06.jpg)
CVS5
![CVS5](../../wp-content/themes/levex/img/products/05/img_07.jpg)
![CVS5](../../wp-content/themes/levex/img/en/products/05/img_08.jpg)
CVS5(Built-in resin case type)
![CVS5(Built-in resin case type)](../../wp-content/themes/levex/img/products/05/img_09.jpg)
![CVS5(Built-in resin case type)](../../wp-content/themes/levex/img/en/products/05/img_10.jpg)
(Options) CV05 sync board
Purpose
When multiple sensors of the same type are used, periodic interference noise may occur in the output.
To counter this, noise is reduced by synchronizing the signal generation circuits in each amplifier.
To counter this, noise is reduced by synchronizing the signal generation circuits in each amplifier.
Lineup
For 2 axes
![For 2 axes](../../wp-content/themes/levex/img/products/05/img_11.jpg)
![For 2 axes](../../wp-content/themes/levex/img/en/products/05/img_12.jpg)
For 4 axes
![For 4 axes](../../wp-content/themes/levex/img/products/05/img_13.jpg)
![For 4 axes](../../wp-content/themes/levex/img/en/products/05/img_14.jpg)
For 6 axes
![For 6 axes](../../wp-content/themes/levex/img/products/05/img_15.jpg)
![For 6 axes](../../wp-content/themes/levex/img/en/products/05/img_16.jpg)
Precautions for use
– Only connect sensors and amplifiers with the same serial numbers.
– The master amplifier is fixed.
– Slave amplifiers do not operate in isolation.
– Operation with a reduced number of slave amps connected is possible if they are the same model.
– The master amplifier is fixed.
– Slave amplifiers do not operate in isolation.
– Operation with a reduced number of slave amps connected is possible if they are the same model.
Output – power cable
Connection configuration
![Connection configuration](../../wp-content/themes/levex/img/en/products/05/img_17.jpg)
Standard
Cable: Dedicated 4-core cable (Length:2m)
End treatment – Amplifier side : With connector / Measuring instrument side : Unfinished
End treatment – Amplifier side : With connector / Measuring instrument side : Unfinished
![Connection configuration](../../wp-content/themes/levex/img/en/products/05/img_18.jpg)
(End treatment example) * We fit a range of connectors.
(Signal side) With BNC conversion cable
![(Signal side) With BNC conversion cable](../../wp-content/themes/levex/img/en/products/05/img_19.jpg)
(Signal side) BNC conversion cable + (Power supply side) Banana plug
![(Signal side) BNC conversion cable + (Power supply side) Banana plug](../../wp-content/themes/levex/img/en/products/05/img_20.jpg)
(Signal line) With Tajimi Electronics connector
![(Signal line) With Tajimi Electronics connector](../../wp-content/themes/levex/img/en/products/05/img_21.jpg)